VapeWholesaleHub  |  Wholesale supplier · Shenzhen, China
Tel / WeChat / WhatsApp: +86 13711127975  |  vape@0099933.xyz
Home  /  Starter Vape Kit  /  Starter Vape Kit pallet template guide
starter vape kits · brand owners

Starter Vape Kit pallet template guide

There is no shortage of suppliers quoting starter vape kit. The scarce thing is a supplier who will tell you which SKU to drop. We have been shipping starter vape kits long enough to know that the honest answer is usually a shorter list, and that is the answer we give.

Published 28 May 2025  ·  VapeWholesaleHub  ·  Reading time 9 min

Unit from the retained reference sample held against this order number.
Unit from the retained reference sample held against this order number.
Starter Vape Kit pallet template guide configuration from a production run, photographed before packing.
Starter Vape Kit pallet template guide configuration from a production run, photographed before packing.
Finish and assembly detail checked against the approved reference sample.
Finish and assembly detail checked against the approved reference sample.

What we test before a carton is sealed

Buyers come to us for starter vape kit after a bad quarter: dead stock on one side, empty shelves on the other. The cause is usually the same, an assortment built from a catalogue instead of from sell-through data. This page explains how we rebuild that balance for brand owners.

Every batch is pulled from running production, not from a display shelf. We check draw resistance, airflow balance, charge behaviour, leak performance after a temperature shift, finish quality and carton integrity, and we keep the pull records against the order number.

Leak complaints almost always trace back to one of three things: an over-torqued centre post, a seal that sat in a hot container, or a fill volume pushed past the design limit. We cap fill volume slightly below maximum for exactly that reason.

Labels, closures and traceability

Labels are where good orders go wrong. Nicotine warnings, child-resistant closures, batch coding and market-specific text all have to be correct before the pallet leaves. We prepare test reports, declaration of conformity and safety data sheets for each shipment and we ask for your destination list early so artwork matches the market.

If you sell into a market that requires child-resistant packaging, say so at quotation stage. Retrofitting a CR closure onto a finished bottle design usually means a new mould and a four week delay.

For brand owners, the practical answer is usually a shorter range: two core lines, one step-up, one trial SKU. Everything else is inventory risk wearing a nice finish.

What a sensible opening order looks like

Colour range is where assortments quietly die. Six finishes look impressive in a brochure and disastrous on a shelf with 40 cm of space. We recommend two finishes per core SKU and let the trial line carry the novelty.

The first question we ask is not what you want to spend. It is what your customer already buys. Answer that and the starter vape kit list writes itself; skip it and you end up with a pallet of stock that photographs well and sells badly.

  • Document pack prepared per destination market
  • Reference sample retained from every batch
  • Artwork proof plus physical dummy for custom packaging
  • Standing reorder schedule with a fixed cut-off
  • Cartons drop-tested and pallet-counted for clean freight
  • Consolidated or split shipping, quoted both ways

Merchandising a small range well

Seasonality in starter vape kits is real but smaller than most buyers assume. The bigger swing comes from restocking discipline, not from calendar events.

Photography matters for online listings. Shoot on a neutral background with the device at a slight angle, show the pack alongside the unit, and keep the same framing across the range so the grid reads as a family.

Specification summary

Typical specification for this category
Battery800 mAh
Pod capacity2.5 ml
Coil resistance0.8 ohm
IncludedDevice, pod, cable
ChargingUSB-C 5V/1A
PackagingBlister pack
Minimum order200 units per SKU, mixed cartons allowed
Lead time22 working days after artwork approval

We would rather lose an order at quotation stage than explain a mismatch after delivery, which is why the specification conversation comes before the price conversation.

Frequently asked

What is the minimum order for starter vape kit?

Standard configurations start at 300 units per SKU, with mixed SKUs allowed inside the same carton. Custom colours, custom packaging or a private label run usually start at 800 units because of setup time on the line.

Do you support private label?

We do. Send your artwork or your brand direction and we will return a digital proof, then a physical dummy for colour approval. Packaging files stay on record so a rebrand later is a file update rather than a redesign.

Can we order samples before committing?

Yes. Sample orders are shipped by air express and the cost is credited against your first production order above 300 units. We would rather you handle the sample than approve a specification from a photograph.

Related reading

Need a quotation on starter vape kits?

Send destination market, target price and quantity. Same-day reply on working days.

Tel / WeChat / WhatsApp +86 13711127975  ·  vape@0099933.xyz

Talk to the supply team

Ask for a quotation on starter vape kits

Tell us the market you sell into and the price band you work in. You will get a specification and a landed cost estimate, not a catalogue dump.

What to send

Destination market, target retail price, quantity per SKU, and whether you need private label. With those four lines we can quote the same day.

Samples ship by air express and the cost is credited against your first production order.

Email the team
WhatsApp Email us