VapeWholesaleHub  |  Wholesale supplier · Shenzhen, China
Tel / WeChat / WhatsApp: +86 13711127975  |  vape@0099933.xyz
Home  /  Starter Vape Kit  /  Starter Vape Kit PO terms: for buyers
starter vape kits · brand owners

Starter Vape Kit PO terms: for buyers

This page is for brand owners who want a working answer on specification, price and lead time before they commit a purchase order. We have written the detail down so nobody has to sit through a sales call to extract it.

Published 08 November 2025  ·  VapeWholesaleHub  ·  Reading time 9 min

Surface finish under raking light, one of the cosmetic checks.
Surface finish under raking light, one of the cosmetic checks.
Starter Vape Kit PO terms configuration from a production run, photographed before packing.
Starter Vape Kit PO terms configuration from a production run, photographed before packing.

How orders move from factory to shelf

We work with brand owners who order between a few hundred and a few thousand units at a time, and we treat both ends the same way: a written specification, a sample you approve, and a production run that matches the sample.

Damage in transit is nearly always a packing decision, not bad luck. Double-walled cartons, internal dividers and a drop-tested configuration cost a little more and save the argument at the other end.

Transit times move with the season. Book space early for Q4 and around Chinese New Year, when factory output pauses for two to three weeks and freight rates tighten at the same time.

Where defects actually come from

Leak complaints almost always trace back to one of three things: an over-torqued centre post, a seal that sat in a hot container, or a fill volume pushed past the design limit. We cap fill volume slightly below maximum for exactly that reason.

Battery safety is not a marketing line. Cells are matched by capacity and internal resistance before assembly, charging boards are checked for cut-off voltage, and any unit that fails the cut-off test never reaches packing.

For brand owners, the practical answer is usually a shorter range: two core lines, one step-up, one trial SKU. Everything else is inventory risk wearing a nice finish.

Assortment planning without the guesswork

The first question we ask is not what you want to spend. It is what your customer already buys. Answer that and the starter vape kit list writes itself; skip it and you end up with a pallet of stock that photographs well and sells badly.

We source starter vape kits from a small group of factories we have worked with for years. That means a specification can be held across repeat orders instead of being re-qualified from scratch every quarter. Consistency is a boring selling point and it is also the entire game.

  • Cartons drop-tested and pallet-counted for clean freight
  • Named account contact who has handled the product
  • Seven-day defect reporting with replace-or-credit
  • Document pack prepared per destination market
  • Specification locked in writing before production starts
  • Consolidated or split shipping, quoted both ways

Merchandising a small range well

Bundle a device with a consumable and the reorder rhythm changes from occasional to weekly. That single merchandising decision often does more for monthly revenue than a price promotion.

Staff knowledge converts better than any poster. If your team can explain the difference between two coils in one sentence, the step-up SKU sells itself.

Specification summary

Typical specification for this category
Battery500 mAh
Pod capacity3.0 ml
Coil resistance1.0 ohm
IncludedDevice, 2 pods, cable
ChargingUSB-C 5V/1A
PackagingBlister pack
Minimum order200 units per SKU, mixed cartons allowed
Lead time18 working days after artwork approval

None of this is complicated. It is just written down, which is more than most buyers get before they wire a deposit.

Frequently asked

How long does production take?

Around 25 working days after artwork approval for stock configurations, plus transit. Custom runs add roughly a week for tooling and a physical dummy. We confirm the date in writing on the order acknowledgement.

How do you handle repeat orders?

The specification is held on file against your account, so a reorder is a reference rather than a new brief. We recommend a standing schedule with a fixed weekly cut-off so stock lands before the shelf empties.

What happens if part of the order is defective?

Report within seven days with photos and the batch code. Confirmed defects are replaced or credited on the next shipment. The failure is logged by mode and batch, and reviewed monthly with the factory.

Related reading

Need a quotation on starter vape kits?

Send destination market, target price and quantity. Same-day reply on working days.

Tel / WeChat / WhatsApp +86 13711127975  ·  vape@0099933.xyz

Talk to the supply team

Ask for a quotation on starter vape kits

Tell us the market you sell into and the price band you work in. You will get a specification and a landed cost estimate, not a catalogue dump.

What to send

Destination market, target retail price, quantity per SKU, and whether you need private label. With those four lines we can quote the same day.

Samples ship by air express and the cost is credited against your first production order.

Email the team
WhatsApp Email us