VapeWholesaleHub  |  Wholesale supplier · Shenzhen, China
Tel / WeChat / WhatsApp: +86 13711127975  |  vape@0099933.xyz
Home  /  Starter Vape Kit  /  Starter Vape Kit private label artwork for distributors
starter vape kits · brand owners

Starter Vape Kit private label artwork for distributors

We ship starter vape kits to distributors, chain buyers and independent shops. What follows is the material we normally cover in a first conversation: what we hold in stock, how we test it, how it ships, and what happens when a carton arrives damaged.

Published 29 November 2025  ·  VapeWholesaleHub  ·  Reading time 8 min

Finish and assembly detail checked against the approved reference sample.
Finish and assembly detail checked against the approved reference sample.
Starter Vape Kit private label artwork for distributors configuration from a production run, photographed before packing.
Starter Vape Kit private label artwork for distributors configuration from a production run, photographed before packing.

Batch consistency and why it matters

Buyers come to us for starter vape kit after a bad quarter: dead stock on one side, empty shelves on the other. The cause is usually the same, an assortment built from a catalogue instead of from sell-through data. This page explains how we rebuild that balance for brand owners.

Leak complaints almost always trace back to one of three things: an over-torqued centre post, a seal that sat in a hot container, or a fill volume pushed past the design limit. We cap fill volume slightly below maximum for exactly that reason.

Flavour drift between batches is the quiet killer of repeat orders. We retain a sealed reference sample from every run so a complaint six weeks later can be compared against what actually left the building.

Unit price versus landed cost

Freight is quoted separately and honestly. Bundling it into the unit price looks tidy and hides the one line that changes most often between shipments.

Unit price breaks usually land at 500, 1000 and 2000 pieces. Between those steps the cost curve flattens, which is why pushing a 200 unit order to 500 often costs less per unit than buyers expect.

For brand owners, the practical answer is usually a shorter range: two core lines, one step-up, one trial SKU. Everything else is inventory risk wearing a nice finish.

Compliance without the last-minute scramble

Regulation for starter vape kits differs by country and sometimes by state. We do not pretend to be your lawyer, but we do keep the document pack current and we will tell you when a configuration cannot legally enter a market you have named.

If you sell into a market that requires child-resistant packaging, say so at quotation stage. Retrofitting a CR closure onto a finished bottle design usually means a new mould and a four week delay.

  • Named account contact who has handled the product
  • Specification locked in writing before production starts
  • Batch codes traceable from carton back to production date
  • Artwork proof plus physical dummy for custom packaging
  • Standing reorder schedule with a fixed cut-off
  • Reference sample retained from every batch

After-sales, replacements and reorders

Every account gets a named contact who has actually seen the product. Being passed between three people to answer one question about a coil resistance is the fastest way to lose a buyer, so we do not organise support that way.

For private label accounts we hold the artwork files and the approval record. Rebranding a line eighteen months later is then a file update instead of a redesign.

Specification summary

Typical specification for this category
Battery800 mAh
Pod capacity2.0 ml
Coil resistance0.8 ohm
IncludedDevice, pod, cable
ChargingUSB-C 5V/1A
PackagingRetail box
Minimum order200 units per SKU, mixed cartons allowed
Lead time30 working days after artwork approval

The detail above is what we hold ourselves to on every shipment, including the small ones. It is also the list we will walk through with you before the first order.

Frequently asked

What happens if part of the order is defective?

Report within seven days with photos and the batch code. Confirmed defects are replaced or credited on the next shipment. The failure is logged by mode and batch, and reviewed monthly with the factory.

How do you handle repeat orders?

The specification is held on file against your account, so a reorder is a reference rather than a new brief. We recommend a standing schedule with a fixed weekly cut-off so stock lands before the shelf empties.

How long does production take?

Around 12 working days after artwork approval for stock configurations, plus transit. Custom runs add roughly a week for tooling and a physical dummy. We confirm the date in writing on the order acknowledgement.

Related reading

Need a quotation on starter vape kits?

Send destination market, target price and quantity. Same-day reply on working days.

Tel / WeChat / WhatsApp +86 13711127975  ·  vape@0099933.xyz

Talk to the supply team

Ask for a quotation on starter vape kits

Tell us the market you sell into and the price band you work in. You will get a specification and a landed cost estimate, not a catalogue dump.

What to send

Destination market, target retail price, quantity per SKU, and whether you need private label. With those four lines we can quote the same day.

Samples ship by air express and the cost is credited against your first production order.

Email the team
WhatsApp Email us